trying to figure out the code on my washer but i unplugged it so now i dont know what to do

If your washing machine is experiencing problems, it may show a code on the display. Each code indicates a dissimilar consequence with your appliance and tin often be fixed without calling an engineer. Employ the tables below to identify the cause of your code and any possible solutions.

If you lot see a check code that isn't listed so try consulting your user manual. If you take tried all possible solutions and the problem persists, please contact your nearest Samsung Service Centre or volume a repair from an engineer.

Delight notation: Do not become confused between number and letter codes. The 5 and the S symbol tin appear like as can the 3 and E. Double bank check your codes if yous can not find them.

Code starts with a number

Washing automobile codes table

0	The drum clean reminder is left on	This is non a fault. This is role of a reminder to run a cleaning cycle. The machine operates normally without running the Pulsate Make clean cycle, but it is recommended to run the cycle regularly for hygiene purposes.
1C  1E	Water level sensor issue	Switch off the apparatus at the mains then wait 1 minute. Switch the appliance back on once again and start a new programme.

Washing auto codes table

3C, 3E, 3E1, 3E2, 3E3, 3E4	Motor issue	Switch off the appliance at the mains and then wait 1 infinitesimal. Switch the appliance dorsum on again and get-go a new plan.
3CP	Electronic control issue	Switch off the appliance at the mains then wait 1 minute. Switch the appliance back on again and beginning a new plan.

Washing car codes table

3CP	Electronic control consequence	Restart the cycle.
4C, 4E	H2o supply issue	Make sure that the h2o tap is opened fully and water is flowing. Check that the water pressure is sufficient (min: 0.5 bar, max: 8 bar). Water flow from the tap should release at least 4 litres / minute. Bank check and make clean the mesh filter. Check that the water supply hose is not clogged or kinked. Cheque that the drain hose is secured at the right superlative. For farther assistance, picket our video: How to resolve a 4E or 4C lawmaking.

Washing machine codes table

4C2, 4E1, 4E2, 4Ed	Water temperature outcome	Check that your water hose is connected to a cold supply and not a hot supply. Cold water is usually indicated by a blue tap.
5C, 5E	Water drainage upshot	Use the emergency hose to drain excess water from the pulsate. Clean the bleed pump filter. Check the drain hose and waste connection for any kinks and blockages. Brand sure the drain hose isn't clogged and that information technology is straightened all the way to the drain system. The outlet bleed hose should exist installed at a acme of at least 60cm. For further assist, watch our video: How to resolve 4E or 5E codes

Washing machine codes tabular array

6E	Water heater non functioning	Delight contact the Samsung Service Centre.
8C	MEMS sensor upshot	Turn the appliance off and restart the cycle.

5

8E	Current fault	Switch off the appliance at the mains then await 1 minute. Switch the appliance dorsum on again and first a new program.
9E1, 9E2, 9H1	Power mistake	Switch off the appliance at the mains and wait 1 minute before switching it back on again. If this doesn't fix the issue, brand sure that the socket the appliance is plugged into is working. If there is yet no power, you may need to replace the fuse in the washing machine plug. For assistance contact Samsung support.

Washing machine codes table

11E	Low water level detected	Check that the level of the drain hose is not lower than the base of the washing machine. Make sure the finish of the bleed hose is placed on the flooring and that it is non clogged. Check for a water leak. If there is no sign of whatever h2o, switch off the power for  ane minute. Reconnect information technology, then try once more.
12E	Push issues	Check to run into if any of the buttons are sticking. Disconnect the apparatus from the mains and make clean the buttons with a lightly dampened cloth.

Washing automobile codes table

13E	Bespeak communication error	Wait for a few minutes, the auto may automatically return to normal operation. If it doesn't, turn the machine off and restart the bicycle.
14E	Button issues	Bank check to see if whatever of the buttons are sticking. Disconnect the appliance from the mains and clean the buttons with a lightly dampened textile.

Code starts with a letter of the alphabet

Washing machine codes tabular array

AC6, AC, AE	Point advice mistake	Look for a few minutes, the machine may automatically return to normal functioning. If information technology doesn't, plough the auto off and restart the cycle.
bE1, bE2, bE3	Button issues	Check to see if whatever of the buttons are sticking. Disconnect the appliance from the mains and clean the buttons with a lightly with a dampened textile.

Washing machine codes table

CE	Water temperature issue	Bank check that your water hose is continued to a cold supply and not a hot supply. Cold water is usually indicated by a blue tap.
Cb	Calibration mode	This is non a fault. Press Commencement/Pause to run the Calibration cycle and look for 0 when it is complete

Washing motorcar codes table

dC, DC, DC1, dE, dE1	Door issues	Check that the door is fully closed and that nothing is trapped in the door. Check your apparatus manual for optimum loading. For problems with child lock read our FAQ on how to turn child lock off on your washing car.
DC3	Add door lock issue	Plow the machine off, and restart the wheel. For issues with child lock read our FAQ on how to plough child lock off on your washing auto.

Washing machine codes tabular array

DDC, ddC	The Add Door was opened without pressing commencement/interruption	Press the Add Door closed so printing start/break to try again. For issues with child lock read our FAQ on how to turn child lock off on your washing machine
dE2	On / Off switch error	Disconnect the appliance from the mains, look for 5 minutes and then attempt over again.

Washing machine codes tabular array

E1	Water supply issue	Make sure that the water tap is opened fully and water is flowing. Cheque that the h2o pressure is sufficient (min: 0.5 bar, max: 8 bar). Water flow from the tap should release at least iv litres / minute. Check and make clean the mesh filter. Check that the water supply hose is not clogged or kinked. Check that the drain hose is secured at the right acme. For farther assistance, picket our video:How to resolve a 4E or 4C code
E2	H2o drainage outcome	Employ the emergency hose to drain excess water from the drum. Make clean the drain pump filter. Check the drain hose and waste material connectedness for any kinks and blockages. Make sure the drain hose isn't clogged and that it is straightened all the way to the bleed arrangement. The outlet bleed hose should be installed at a peak of at to the lowest degree 60cm. For further assistance, watch our video: How to resolve 4E or 5E codes.

Washing automobile codes table

E3	Overflow error	Too much washing powder/liquid may accept been added. Switch off the power to the apparatus, and so wait one minute. Switch the power supply back on. The drain pump should drain the washing machine.
E4	The load in the drum is unbalanced	This is non a fault. The appliance has detected an unbalanced load and has stopped the spin for safety reasons. Make sure the appliance is on a flat, stable surface. Redistribute washing by adding or removing items to create a more balanced load. Unmarried large/heavy items such every bit bath mats and big towels are unlikely to spin on their ain. Please add together two/three additional towels and put on another spin cycle.

Washing auto codes table

E5, E6	Water heater not operation	Please contact the Samsung Service Eye.
E7	Water level sensor issue	Switch off the appliance at the mains then expect i minute. Switch the appliance back on again and outset a new plan.

Washing machine codes table

E8	H2o temperature outcome	Check that your water hose is connected to a cold supply and not a hot supply. Cold water is unremarkably indicated past a bluish tap.
E9	Depression water level detected	Check that the level of the drain hose is non lower than the base of the washing machine. Make sure the end of the drain hose is placed on the floor and that it is non clogged. Check for a h2o leak. If there is no sign of any water, switch off the power for i minute. Reconnect it, and then try again.

Washing machine codes table

EA, EB	Motor consequence	Switch off the apparatus at the mains then wait 1 minute. Switch the appliance back on again and start a new program.
EC	Temperature sensor mistake	Switch the appliance off at the mains then expect i minute. Switch the apparatus back on again and start a new programme.

Washing automobile codes tabular array

FE	Fan error	Delight contact the Samsung Service Eye.
H1, HC, HE	Water temperature consequence	Check that your water hose is connected to a cold supply and not a hot supply. Cold h2o is usually indicated by a blue tap.

Washing motorcar codes tabular array

HE1	Water heater not functioning	Please contact the Samsung Service Eye.
HE2	Dryer heater not functioning	The dryer section has shut downward for safety reasons equally the apparatus detected that the temperature was getting too hot.

Washing car codes table

HE3	Steam office non operating normally	Please contact the Samsung Service Heart.
HOT	Apparatus is also hot	This is non a mistake. This code means the appliance is too hot. The appliance fan will go on to run until the apparatus has cooled downwards plenty for the washing to exist removed (55°C). Once it has cooled, the door will unlock.

Washing machine codes tabular array

LC, LC1, LE, LE1	Low water level detected	Check that the level of the drain hose is non lower than the base of operations of the washing machine. Check for a water leak. If there is no sign of any water, switch off the power, reconnect and try once again.
OC, OE, OF	Overflow error	Too much washing pulverisation/liquid may have been added. Switch off the ability to the appliance, wait i minute and so switch the ability supply back on. The drain pump should drain the washing automobile.

Washing auto codes tabular array

Plo	Power error	Switch off the apparatus at the mains and expect 1 minute before switching it back on again. If this doesn't fix the consequence, brand sure that the socket the appliance is plugged into is working. If there is yet no ability, you may need to supercede the fuse in the washing machine plug.
Sud	Too much cream is detected	The appliance volition unremarkably fix this on its ain, however if it doesn't you will need to run either an Eco drum clean bicycle or a ninety°C cotton wool wheel with no detergent or washing load. If the code remains, check the drain pump filter and make clean the water supply hose mesh filter, so run a spin wheel to drain the water from the appliance. If at that place is an accumulation of pulverisation detergent, repeat the "Eco Drum Make clean" cycle.

Washing auto codes tabular array

t1, t2, tSt	The appliance is in exam mode	Switch off the appliance at the mains then wait 1 infinitesimal. Switch the apparatus on again and start a new program.
tE, tE1, tE2, tE3, tC1, tC2, tC3	Temperature sensor error	Switch the appliance off at the mains then wait 1 infinitesimal. Switch the appliance back on once more and beginning a new plan.

Washing machine codes table

Ub, UE	The load in the drum is unbalanced	This is not a error. The apparatus has detected an unbalanced load and has stopped the spin for safety reasons. Brand sure the appliance is on a flat, stable surface. Redistribute washing by adding or removing items to create a more counterbalanced load. Single large/heavy items such as bath mats and big towels are unlikely to spin on their own. Add 2/3 boosted towels and put on another spin cycle. For further assist, watch our video: My washing machine is showing a UE code during a spin wheel.
UC	Fluctuation in the supply voltage	Check the ability cord is plugged in properly. Switch off the appliance at the mains so expect i infinitesimal. Check to make sure the washing automobile is not continued to whatever other apparatus or to an extension cable. Switch the appliance back on over again and start a new plan.

Buttons, symbols and icons Click to Expand

At that place are many different symbols, buttons and icons that are used on Samsung devices. These are designed to provide information apace and clearly. Symbols and icons displayed on your washing motorcar are non the same as codes. Rather than telling you that something is wrong, icons allow yous know what your washing machine is doing and provide extra data. The buttons used can look very like to the symbols and often stand for with them. It is useful to sympathize what both mean.

Please note: Available icons and their appearance will vary betwixt models.

The T-Shirt with a + icon indicates that you can suspension the bicycle to add more clothing. Some washing machines accept an Addwash door, making it even easier to add wear during a cycle.

For badly soiled laundry. When this light is on the functioning time for each bicycle is longer than normal.

The smiley confront icon indicates that Kid Lock has been turned on. All buttons on your washing machine other than the power button and the control punch are disabled. On some washing machines, the door will also be locked. Read our FAQ on how to switch the child lock off on your Samsung washing machine for assistance turning your child lock on and off.

The padlock (without a smiley face) or the central icon indicates that the door is locked. The washing machine door will lock whenever a bike is in progress or it is unsafe to open the door. Do not attempt to open up the door while this icon is lit.

The clock icon indicates that delay showtime is in utilise. Delay showtime prepares a bicycle to begin at a designated time.

The hourglass icon indicates how much time is left in the wheel. The number shown on the display while the hourglass appears is the time remaining.

The crossed out speaker icon and the crossed out bell indicate that the signal sounds that happen at the end of a cycle have been turned off. To plough sounds on or off  hold down the spin and options buttons simultaneously for three seconds.

The icon of a washing car drum will be displayed later on a certain number of washes. The number will vary depending on your washing auto model. This icon lets yous know that a cleaning cycle should exist run.

The button with a sink and no + icon is used to set the rinse count for a current bike. You lot can set the rinse count to a max of 5, depending on the cycle.

The sink of water with a + icon indicates that the extra rinse characteristic has been turned on. Extra rinse adds additional time onto the rinse portion of the wheel to help remove laundry additives and perfumes.

The clouds icon indicates that the steam choice has been turned on. Steam is used to meliorate stain treatment and use less water when washing colourfast clothing.

The lightbulb icon indicates that the light inside the washing machine has been turned on.

When the no spin icon is on the drum will not spin after the terminal drain process. Employ the spin button to change between spin settings.  To apply no spin, press the spin button until the no spin indicator turns on.

The light adjacent to this symbol will calorie-free upwardly when the chimera soak role is activated. This function helps remove a wide multifariousness of stubborn stains.

This will add together a preliminary washing cycle before the main wash cycle.

Use to select between different options on your washing motorcar.

The temperature push button is used to arrange the temperature for the electric current cycle.

Easy atomic number 26 operates alongside certain wash cycles to make ironing dress easier by reducing wrinkles during the spin.

This is a way used to get detailed information about issues that occur with your washing machine using the SmartThings app. To enter smart check fashion hold downwards the options and delay end buttons.

The Wi-Fi icon indicates that your washing machine is connected to your home's Wi-Fi and the SmartThings app. Some models also back up the Smart Home and Smart Washer/Dryer apps.

Enabling Smart Control lets you lot control the appliance using the Smart Things app. If you have non enabled Smart Control, you can monitor the appliance, but you will non be able to control information technology remotely.

If you are after solutions for incorrect linguistic communication on your washing machine read our FAQ on how to alter the language on your laundry U washing machine to set your washing automobile to the right language.

cookblithad89.blogspot.com

Source: https://www.samsung.com/uk/support/home-appliances/what-do-the-codes-on-my-washing-machine-mean/

Share this post